Can't see it.
It looks like the NW pic has a big hum superimposed.
SE would result from weird rectification, so maybe the 6AL5 is duff.
Please re-post picture.
Scratch 2ch Sta-Level Build
- Thread starter StarTrucker
- Start date
Help Support GroupDIY Audio Forum:
It looks like the NW pic has a big hum superimposed.
SE would result from weird rectification, so maybe the 6AL5 is duff.
Please re-post picture.
from the audio files it seems is not compressing or compressing too fast, maybe there's an error in the single double switch? very easy to make errors there.
check for capacity and resistance from 6al5 output to gnd in single mode.
or check the bias on 6ba6's. the cathode usually have to sits from 3 to 8 volts, less than thet you have too much gain.
or try replace the 12at7 with a 12au7 and check if the feedback from 6v6 to 12at7 is wired properly.
check for capacity and resistance from 6al5 output to gnd in single mode.
or check the bias on 6ba6's. the cathode usually have to sits from 3 to 8 volts, less than thet you have too much gain.
or try replace the 12at7 with a 12au7 and check if the feedback from 6v6 to 12at7 is wired properly.
Repost of the 6AL5 plates scope.
I left out the single/double switch. attached side chain schemo
View attachment IMG_7041.MOV
I left out the single/double switch. attached side chain schemo
View attachment IMG_7041.MOV
Last edited:
Can't see the pic.
Last edited:
The dual potentiometer creates a virtual center tap.
Updated the last post with pics.
Yes original schemo has a 220k load resistor across the secondary in parallel with the dual pot, no CT
Last edited:
Fixed that last switch problem.
So, still distortion on compression and freak out on the scope
Grounded the center of the dual pot to test the amp wide open. Here is the sine wave at pin2 of the output xlr. Distortion on the leading edge
Here is the xlr pin 2 with the sidechain engaged. rolling the input knob from 8 to 9 o'clock is when it kicks in.
View attachment ScopeCompression.mp4
And the input of the sidechain at the same point when compression kicks in. The pot in my diagram is wired up as a rheostat. Should that matter? Everything else in the sidechain is the same as the schemo Abbey corrected.
View attachment SidechaintoComp.mp4
So, still distortion on compression and freak out on the scope
Grounded the center of the dual pot to test the amp wide open. Here is the sine wave at pin2 of the output xlr. Distortion on the leading edge
Here is the xlr pin 2 with the sidechain engaged. rolling the input knob from 8 to 9 o'clock is when it kicks in.
View attachment ScopeCompression.mp4
And the input of the sidechain at the same point when compression kicks in. The pot in my diagram is wired up as a rheostat. Should that matter? Everything else in the sidechain is the same as the schemo Abbey corrected.
View attachment SidechaintoComp.mp4
Can you probe the voltage there at various levels.
no input signal = 0vdc .085vac
Input signal but no compression (stable sine wave in the last post) - 0vdc, .027vac
Input signal and compression (freaky waveform on the scope in the last post) - Jumps rapidly between .1v, 3v, and 6v DC, jumps around between 1.3 to 3.3vac
max Input signal and compression - Jumps around rapidly between 8,12, and 18v DC, jumps around in the range of 4 to 6.4vac
Input signal but no compression (stable sine wave in the last post) - 0vdc, .027vac
Input signal and compression (freaky waveform on the scope in the last post) - Jumps rapidly between .1v, 3v, and 6v DC, jumps around between 1.3 to 3.3vac
max Input signal and compression - Jumps around rapidly between 8,12, and 18v DC, jumps around in the range of 4 to 6.4vac
Last edited:
Well, this is not normal. There should not be rapid variations.
Either the 0.47uF is disconnected or defective, or there is something that discharges it.
Victory! Bad wiring from the controls on the faceplate to the circuit was responsible for a lot of the voltage bouncing around. It was unstable at the fast setting but connecting both the .47uf and 1uf cap in all positions solved it.
Now the only thing is that the meters don't return to zero but get stuck around -3dB. Just add a trim pot between meter and ground and adjust til it's right?
Thank you to everyone who offered their knowledge and help!!
Now the only thing is that the meters don't return to zero but get stuck around -3dB. Just add a trim pot between meter and ground and adjust til it's right?
Thank you to everyone who offered their knowledge and help!!
I don't doubt it but it would make the attack and release times too long for single operation, which requires only the 0.47uF.
Got rid of the 1uf cap, cleaned up the wiring, replaced the 6al5. All is well and the unit sounds great and is solid even at higher gain reduction levels. Thank you for walking me through this!
