jsteiger

Re: [BUILD]CAPI 2-ACA-Bo~Official Support Thread
« Reply #460 on: November 14, 2017, 11:38:47 PM »
What fader is it and how do you have it wired?
Visit the CAPI store at http://www.capi-gear.com

CAPI is not affiliated with, endorsed by, or sponsored by API.


Re: [BUILD]CAPI 2-ACA-Bo~Official Support Thread
« Reply #461 on: November 15, 2017, 12:44:06 AM »
I'll have to double check after work, fairly certain the 200b is 10k faders all round. 22k bus resistors.
And as for wiring I replicated it from pictures from the below 200b/CAPI thread.

https://groupdiy.com/index.php?topic=54847.0

jsteiger

Re: [BUILD]CAPI 2-ACA-Bo~Official Support Thread
« Reply #462 on: November 15, 2017, 09:15:03 AM »
I'll have to double check after work, fairly certain the 200b is 10k faders all round. 22k bus resistors.
And as for wiring I replicated it from pictures from the below 200b/CAPI thread.

https://groupdiy.com/index.php?topic=54847.0
Looks like he was having the same issue...
Visit the CAPI store at http://www.capi-gear.com

CAPI is not affiliated with, endorsed by, or sponsored by API.

punk

Re: [BUILD]CAPI 2-ACA-Bo~Official Support Thread
« Reply #463 on: August 27, 2018, 09:14:34 PM »
installed, finally, into a soundworkshop SW34. very easy mod and sounds great.
thanks Jeff!!
byron

Re: [BUILD]CAPI 2-ACA-Bo~Official Support Thread
« Reply #464 on: September 21, 2018, 02:50:38 PM »
Hello,
I want to upgrade my D&R 8000's master section with the ACA Booster and stumbled upon two questions.
The master bus on the 8000 is fed through 12k resistors (see first picture). Can I put a 35k resitor in front of the ACA input to get to 47k ? Or how do I recalculate the feedback resistors and caps on the ACA?

And can you give me some tips where I should bypass the original master section? My first thought was to go from the master bus and return before the insert point (see second picture). But then I would loose the monitor bus. And I would like to keep the original insert point. Where would you set the bypass points?

thank you
Arne
« Last Edit: September 21, 2018, 06:19:03 PM by a_wachtmann »

boji

Re: [BUILD]CAPI 2-ACA-Bo~Official Support Thread New
« Reply #465 on: November 18, 2018, 12:31:06 PM »
Hello Jeff, I'm using your rather essential aca/bo for the ends of my mixer, thank you!  I got into a discussion I was gifted with advice about ideas on an aux group send/return module from a few folks, and Abby mentioned the value of using a 990 for its low noise.  Do I remember correctly you saying somewhere you chose to use a 990 for your aca's on the pgm bus?  If so, does that require modifying the pcb's you sell or just changing some resistors/caps?
« Last Edit: November 18, 2018, 12:39:21 PM by boji »


 

Related Topics

  Subject / Started by Replies Last post
971 Replies
165158 Views
Last post April 27, 2018, 06:45:54 PM
by jsteiger
138 Replies
31401 Views
Last post November 26, 2018, 09:42:20 AM
by [silent:arts]
335 Replies
59175 Views
Last post December 12, 2018, 03:41:08 PM
by poserp
16 Replies
2802 Views
Last post November 03, 2018, 04:12:44 PM
by fragletrollet