table top fader unit
« on: November 20, 2004, 12:52:20 PM »
Several of the new line mixers and "DAW summing units" include pre-wired connections for external faders, in place of the existing rotary pots.  In my situation, it is only for the main stereo output, not all of the individual input channels.  So I'm looking at either a single stereo fader or a pair of mono faders.  As I already mentioned, the mixer has a connection for easy attachment of the faders, and the P&G faders come pre-wired on the other end; so the signal connection is not a problem.  But I'm lost when it comes to a simple design for a table top box to mount this fader(s).   Has anyone ever built anything like this and can you post a photo or some suggestions?

I'm almost considering the purchase of an old fader module from a Telefunken-type console that used fully enclosed modular faders. Although the module box is too deep for what I'm trying to do,  I could at least steal the slotted plate for the fader button to ride through.  Then I would just have to mount that plate into a box of some sort.  But I'm hoping that one of you have a better solution, and one that does not require that I have a metal fabrication shop in my basement.  (hell, I don't even have a basement......)

Thanks
Steve
Lexington 125  - High Resolution Location Recording

[email protected]
www.lexington125.com


[email protected]

table top fader unit
« Reply #1 on: November 20, 2004, 02:36:11 PM »
Hey Steve,

I think the Mackie "Remote Fader" was mentioned somewhere in another post.

http://www.mackie.com/pdf/archive/cr1604_addons_arch.pdf  

It might be a solution for you.  It's a small chassis with a 100mm stereo fader.  If you don't like the quality of the fader that's included, you could always switch-it-out with something better.   I like the Panasonic faders because of the stereo tracking specifications.  

Problem... I'm sure that it's out-of-production, but I bet Mackie could locate one for you.

We used to recommend these Remote Faders for our XTRAMIX rack mixer customers that wanted to "ride" the stereo level without having a 6' rack towering over them.  

If your DAW summing mixer has a low-Z output for the  fader interface, there's no reason you can't use a 15-25' (well shielded) cable.  We have touring guys that remote a stereo foot pedal from the stage to the XTRAMIX inserts that's over 75'.

Regards,

Vince Poulos
http://www.speck.com
Vince Poulos
Speck Electronics
www.speck.com

table top fader unit
« Reply #2 on: November 20, 2004, 03:45:34 PM »
THANKS, Vince!

Not only does the remote fader look like it will work, but now I finally understand what a MIXERMIXER is!   (I've heard people mention that damn thing for years, and I never had a clue what they were talking about, or I thought that they were stuttering.)

But seriously, the remote fader box is exactly what I need, and I'll even get over my self-imposed fear of anything with a Mackie logo on it.  (I'm sure that I can strip and repaint it so that no one will ever know.......and you guy promise not to tell, right?) The PDF file link you attached even included dimensions that seem to indicate that both P&G 3000 and 8000 series faders *should* fit.

Now if I can just find one of these suckers........
Steve
Lexington 125  - High Resolution Location Recording

[email protected]
www.lexington125.com

daArry

table top fader unit
« Reply #3 on: November 20, 2004, 03:50:40 PM »
what about mcs' relay control pot with the ir option from the other 8 selector thingy...?

table top fader unit
« Reply #4 on: November 20, 2004, 04:34:12 PM »
what about mcs' relay control pot with the ir option from the other 8 selector thingy...?

Huh?
Steve
Lexington 125  - High Resolution Location Recording

[email protected]
www.lexington125.com



 

Related Topics

  Subject / Started by Replies Last post
3 Replies
1842 Views
Last post May 14, 2007, 09:49:04 AM
by SSLtech
2 Replies
2263 Views
Last post October 18, 2007, 08:36:42 AM
by Purusha
4 Replies
1355 Views
Last post February 13, 2011, 09:45:33 AM
by BR
0 Replies
500 Views
Last post August 20, 2018, 01:20:02 PM
by jplebre