LewKellogg

Re: Lukas' PCB Lab (Etching/Designing/Basic Assembly)
« Reply #20 on: June 21, 2016, 05:47:31 PM »
Welcome back!
Lew Kellogg
Kings Mill Audio


livingnote

Re: Lukas' PCB Lab (Etching/Designing/Basic Assembly)
« Reply #21 on: July 21, 2016, 10:58:24 AM »
Hey Lew :) How's it going?

Check this out: Local talent Anna Käse, who runs a print shop in my neighborhood, took one of
the PCBs I made and ran it through her printing press:

« Last Edit: July 21, 2016, 11:01:33 AM by livingnote »
Quote from: emrr
F-in' hook some Sh*t up and see if it catches on fire

Leek

Re: Lukas' PCB Lab (Etching/Designing/Basic Assembly)
« Reply #22 on: August 27, 2016, 09:22:05 PM »
Could you make pcb for the following and look over design to help easy worries that it doesn't work?

livingnote

Re: Lukas' PCB Lab (Etching/Designing/Basic Assembly)
« Reply #23 on: September 13, 2016, 10:17:14 AM »
Hey :)

Sorry for the late reply, I had been checking my mail inbox for DIY messages and not the forum thread itself.

When in doubt, always send a mail to the address that appears when you click on my forum name here in the
thread (livingnote).

Yes, sure I can make a PCB for it, but it would be a design job (and looking over the design itself would also
be design work) - however I can not guarantee that a given circuit will actually do its job as intended - there
are many different designs floating around out there.

Do you have a schematic/source for it and an actual component overlay? Otherwise, it's just the ICs, and
there's no way I can help you unless I know what the components are and how they fit together - even simply
etching something is not readily possible only from this one picture (and looking at those traces I wouldn't
recommend it anyway).

Apart from that - yeah sure, looks like fun.

Cheers,

Lukas
« Last Edit: September 13, 2016, 10:31:12 AM by livingnote »
Quote from: emrr
F-in' hook some Sh*t up and see if it catches on fire

Kid Squid

Re: Lukas' PCB Lab - Etching / Design
« Reply #24 on: February 10, 2017, 09:11:20 AM »
Hi Lukas, I've just emailed you,

Best,
Steve
It is not the same as 4+12, nor is it the same as 4+8, but 4+12 IS the same as 4+8+12....

http://www.facebook.com/LazyLizardLabs

TubeMonkey

Re: Lukas' PCB Lab - Etching / Design
« Reply #25 on: May 09, 2017, 05:34:27 PM »
Hey everybody,
 
I'm back  ;)

Lukas

Hey Lukas! Your inbox is full....   Are the Crush n Blend pcbs still available? Would you be willing to ship to the US?  Thanks in advance!

EB

RuudNL

Re: Lukas' PCB Lab - Etching / Design
« Reply #26 on: May 10, 2017, 07:52:26 AM »
Hey what kind of trimmers are those? Big long things that look like they go way precise.

Looks like they are channel preset potentiometers from a TV tuner!
« Last Edit: May 10, 2017, 07:56:08 AM by RuudNL »
There is a solution for every problem!

http://www.vansteenisaudio.nl

Hobbyist

Re: Lukas' PCB Lab - Etching / Design
« Reply #27 on: June 22, 2017, 04:25:00 AM »
Looks like they are channel preset potentiometers from a TV tuner!

That's right, got it from my fathers backup stock. he repaired a lot of electronics back in the 80's and 90's.
Remember he told me these trimmers were from a VHS-player. They are fun to use, but not super precise

ps: sorry for the late response Lukas :)

ilfungo

Re: Lukas' PCB Lab - Etching / Design
« Reply #28 on: July 12, 2017, 07:29:54 AM »
Hi livingnote
I've tried to PM you but your box is full.
Thanks!

Re: Lukas' PCB Lab - Etching / Design
« Reply #29 on: September 07, 2017, 06:15:57 PM »
Are you able to create a pcb based on a .lay circuit layout file?


livingnote

Re: Lukas' PCB Lab - Etching / Design
« Reply #30 on: September 18, 2017, 06:09:29 AM »
What kind of software is that?
Quote from: emrr
F-in' hook some Sh*t up and see if it catches on fire

dagoose

Re: Lukas' PCB Lab - Etching / Design
« Reply #31 on: October 14, 2017, 05:14:58 AM »
Hey Lukas,

looks like your inbox is full :)

Good to see your back, even though it seems  like you where back for quite some time already :)
I was wondering if still have Crush-N-Blend boards available and how much they are for 1 board (shipping to the netherlands).
I'm building a new mastering console and I was think of adding a wet/dry option to one of the inserts.
Da Goose Music Mastering http://www.dagoosemusic.nl

Potato Cakes

Re: Lukas' PCB Lab - Etching / Design
« Reply #32 on: October 18, 2017, 11:56:58 AM »
Email sent regarding etching for original Opto Grinder.

Thanks!

Paul

audiophreak

Re: Lukas' PCB Lab - Etching / Design
« Reply #33 on: January 03, 2018, 06:48:13 PM »
Hi Lukas ,
                     Glad to see you are back doing this, you made a few PCBs for me a long time ago.  I was wondering if you can make PCBs from PDFs - Kingston's Drive One - here - https://groupdiy.com/index.php?topic=41509.0
" Music washes away from the soul, the dust of everyday life "   ... in loving memory of my Father.

TubeMonkey

Re: Lukas' PCB Lab - Etching / Design
« Reply #34 on: January 17, 2018, 04:36:04 PM »
Hi Lucas,

Still trying to get in touching regarding ordering a few Crush N Blend pcb's. Please direct message me!

Thanks!

EB

thomasdf

Re: Lukas' PCB Lab - Etching / Design
« Reply #35 on: March 20, 2018, 06:10:39 PM »
Hello

Is the Crush n Blend a general dry wet mixing board, or does it only work with the GSSL or such?
Can I use it do add a single mono dry/wet feature to any design?
If yes, I am in for a board or even maybe kit if you have such an offer

Thanks

Thomas

thomasdf

Re: Lukas' PCB Lab - Etching / Design
« Reply #36 on: April 08, 2018, 04:10:24 PM »
Hello

Is the Crush n Blend a general dry wet mixing board, or does it only work with the GSSL or such?
Can I use it do add a single mono dry/wet feature to any design?
If yes, I am in for a board or even maybe kit if you have such an offer

Thanks

Thomas