[toolboxmuziq]

Will these pots work?
100K-Ohm Audio-Taper Potentiometer : Potentiometers | RadioShack.comhttp://www.radioshack.com/100k-ohm-audio-taper-potentiometer/2711722.html

Link doesn't work for me, but 100k audio taper appears correct. Check dimensions for fit.

Ok next question. Do the EL Panels have to light up green? I found blue but I want to be sure before I pull the trigger

[Mulmany]

I got my El panel finally working. ended up having a short. That is now rectified, but I am struggling with an other issue.

The Squish (comp) pot will adjust the output of the panel, but so will the Output pot. I can have the "squish" all the way up, but if I back off the output the El Panel will dim. I am also not seeing compression of the signal, but I do see a change when engaging the Comp/Limit switch.

Any thoughts?

[dmp]

The Squish (comp) pot will adjust the output of the panel, but so will the Output pot. I can have the "squish" all the way up, but if I back off the output the El Panel will dim. I am also not seeing compression of the signal, but I do see a change when engaging the Comp/Limit switch.

I don't think the gain pot should not affect the EL panel at all.

If you aren't seeing compression, be sure the EL panel / cells are enclosed from room light! This thing doesn't work if you can see the EL panel lighting up.

Do the EL Panels have to light up green? I found blue but I want to be sure before I pull the trigger

The cells should react to blue as well, I don't know how the EL panel you have will behave though.
Here's a source from a groupdiy'r if you don't know of it:
https://sites.google.com/site/diypartsstore/catalog/new-t4b-opto-el-panels

[Mulmany]

I don't think the gain pot should not affect the EL panel at all.

@dmp

That's a double negative, hopefully you mean that the gain pot should not affect the EL panel?  Thanks for replying. .. I will look into it more.

[dmp]

Oops- that is not how I meant to write that.
The gain pot is after the gain reduction, so it should not affect the EL panel.

[david.uulf]

hey all did any one else have issues will the comp/limit switch not making any difference and also did you find that the input gain seemed low so you didn't get much compression like only 5db  on max squash??
thanks
dave

[Hummingwire]

Any chance this project will get some new life blown into it again?
I'd love to build one of these 

[Rob Flinn]

Any chance this project will get some new life blown into it again?
I'd love to build one of these 

Not likely from LAZpro.  Peter disappeared off the radar a few years ago.    The last contact I had with hm was a few beers in London about 6 years ago.

[Hummingwire]

Not likely from LAZpro.  Peter disappeared off the radar a few years ago.    The last contact I had with hm was a few beers in London about 6 years ago.

Too bad, I hope he's ok 

Can you (or anyone) recommend another DIY opto comp on here? I tried searching but this was the only one I found.

[Fuzz Face]

Too bad, I hope he's ok 

Can you (or anyone) recommend another DIY opto comp on here? I tried searching but this was the only one I found.

DIYRE has an optical compressor kit

https://www.diyrecordingequipment.com/products/ola5-opto-compressor-kit


Serpent Audio has some LA3A boards
https://serpentaudio.com/product/sa-3a-pcb-blank/

[TwentyTrees]

It's a long shot as it's been a while, but does anyone have any of the docs available for the LAZ LA3A? I recently picked one up second-hand, and though it sounds great there are a few issues which a schematic and / or layout would make it much simpler to troubleshoot. All the links I've found in this thread and elsewhere are long dead.

Thanks!

[dmp]

Too bad, I hope he's ok 

Can you (or anyone) recommend another DIY opto comp on here? I tried searching but this was the only one I found.

DLA2A!
I've built both and the LA2A is the best. It's tube however and bigger.

[dmp]

It's a long shot as it's been a while, but does anyone have any of the docs available for the LAZ LA3A? I recently picked one up second-hand, and though it sounds great there are a few issues which a schematic and / or layout would make it much simpler to troubleshoot. All the links I've found in this thread and elsewhere are long dead.
Thanks!

Yes, I have some docs

[dmp]

layout

[dmp]

board 1

[dmp]

board 2

[dmp]

board 3

[dmp]

BOM

Rename to .xls

[TwentyTrees]

dmp, that is absolutely spectacular - THANK YOU for your help! Raising a glass to you from a grey, rainy London.

LA3a tune up? re-cap?

Started by Vetsen The Lab

diy la3a using perfboard complete info

Started by pucho812 The Lab

Real layout for a LA3A posted

Started by Jim Zuehsow Drawing Board

Laz Pro LA3A 500

Started by kosi Black Market