[BUILD] VC528 ST2+ 500/51x Support Thread...aka The Missing Link!

GroupDIY Audio Forum

Help Support GroupDIY Audio Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Hey jeff,

I am using 2 red dots (both burnt in) from the 2 25's I built up the rack and cabling seem to be ok too...
 
OK. I will post a few "block" test spots so you can narrow down where the problem is at. I am packing orders now so in a few hours.

Best, Jeff
 
Johnny, I have put together a little pdf for this occasion. Hopefully these Troubleshooting Tips will help.

Let me know how you do.

BTW, I have added this link to the bottom of the first post of this thread too.

Cheers, Jeff
 
onward!

Let's dig up the rest of the caps for the main PCB

p804090559-4.jpg


p581342296-4.jpg


Identifying parts again:

p631283205-4.jpg


p562321907-4.jpg


C6 27 pF
p616187207-4.jpg


C5 82pF
p758206955-4.jpg


C29 47pF
p1026079640-4.jpg


Watch the polarity of the electrolytics.  The "-" side is indicated with a solid stripe.
p700108349-4.jpg


And, sidenote here, I managed to melt C20 when I attempted to touch up a solder joint on the front side of the PCB. . . trying to make all perfect solder joints for pictures. . . oh well.  Jeff has been contacted for a replacement WIMA.  In the meantime, since I have 2 kits for a stereo pair, I went ahead and replaced C20 w/ one from the other kit, and the build goes on!

p895349653-3.jpg


Caps installed.

p572505066-3.jpg


Next, I place the trimmer pot RV1

p965991828-3.jpg


And SW1

p976444694-3.jpg


Next, I install the millimax pins for the DOA's.  They are found in this baggie. . . watch out.  These little critters like to run away, and I once spent an hour looking for one on the ground from a VP26 build.

p881517118-4.jpg


p994770259-3.jpg


Insert these from the back side of the PCB.

p910731200-3.jpg


And, solder from the back side.  I set my iron a bit hotter and made sure to flow a proper amount of solder to make these solid as some op amps need to be pressed in pretty hard to seat, and I like these sockets to have a solid mechanical connection to the PCB.

p972934805-3.jpg


p760859703-3.jpg


And, this is how they look from the front side after getting soldered in.
p560581065-3.jpg


And, the main PCB is populated.  Humans win.

p673954430-3.jpg
 
Next up, I install my 3 pin headers for configuring the VC528.  These headers and jumpers are found in this bag:

p280048521-3.jpg


p198819438-3.jpg


This will need to be cut into 5 separate 3 pin units.

p46458774-3.jpg


p22664734-3.jpg


And installed in these locations taking precaution to stand them up perpendicular to the PCB.

p448036349-4.jpg


p236737584-4.jpg


For the next step, I will need my grayhill switches found in this baggie:

p76077927-3.jpg


And use these installed from the front side to align my faceplate to the L-bracket.

p361922299-4.jpg


This will facilitate lining up the mini toggle switches SW3 and SW4

p330824733-4.jpg


p257639370-4.jpg


Holding the switches firmly in place, solder the center lug only.

p531695627-4.jpg


p299533273-4.jpg


Next, locate the PCB mounting hardware.

p375879319-4.jpg


p246284774-4.jpg


Install standoffs and screws as as pictured below.

p352497275-4.jpg


Making sure to leave the front 2 standoffs loose so the screw does not protrude over the top of the standoff.

p451743535-4.jpg


Then, carefully slide the PCB into position.

p383916463-4.jpg


And secure the nuts (without lock washers for now).

p390747615-4.jpg


Confirm proper seating of the mini-toggle switches as well as the PCB being precisely aligned with the L-bracket.

p146137895-4.jpg


And solder the remaining lugs on the mini-toggle switches with the unit assembled.

p228529508-4.jpg


p1061025080-4.jpg


 
Next, I take a close look at the Grayhill switches. . . this particular kit is an early-run kit, and the position stops on the Grayhill switches are pre-installed.  Later versions of the kit will require placing the stop pins as they will utilize a more universal setup on these switches.

p946537461-4.jpg


It is important to position these switches perpendicular to the PCB, and to facilitate this, jsteiger recommends starting with the inner switch, soldering 2 outer rear lugs first, verifying component alignment, and then soldering the front 2 lugs.

p714003743-4.jpg


p881437058-4.jpg


p1014695654-4.jpg


Then, proceed to the outer switch and repeat

p1055605767-4.jpg


p982011902-4.jpg


p557959288-4.jpg


After all is aligned, carefully solder all of the remaining lugs.  Check for solder bridges as these are pretty narrowly spaced.

p659167236-4.jpg

 
Next up are the 2623-1 transformers.

p34515538-4.jpg


Locate the mounting hardware.

p480740588-4.jpg


The component sequence for installation is as follows:  Screw, flat washer, transformer, flat washer, PCB, lock washer, nut.

p160160456-4.jpg


p281715282-4.jpg


p355302854-4.jpg


p832407284-4.jpg


p729533498-4.jpg


And, transformers are positioned on the PCB.

p560362460-4.jpg


Use short segments of shrink wrap to consolidate the wires and solder to the appropriate locations on the PCB keeping the wire runs short.  Be sure to route the wires well clear of the op-amp location.

p667582498-4.jpg


p537821476-4.jpg


p633382061-4.jpg


Next, I install the relay sub-board.  Make sure the relay board does not short out against the transformer.

p994137018-4.jpg


. . .and the discrete follower sub-board. 

p945815863-5.jpg


And, this is where I stopped tonight.

p942515266-4.jpg


p1035978850-4.jpg


The attention put into the design of this kit is pretty phenomenal so far.  I'm looking forward to getting this up and running!
 
Ptownkid said:
wow man, you are great at this!
Yes 'Chung. I was thinking the same exact thing when I went thru the pics this morning. You really make this project look great. Heck, I am thinking of building one.  :eek: ;D  :)

BTW, I have 2 more projects nearing completion. So, reserve some more time for me this winter.  ;)

Best, Jeff
 
jsteiger said:
Yes 'Chung. I was thinking the same exact thing when I went thru the pics this morning. You really make this project look great. Heck, I am thinking of building one.  :eek: ;D  :)

BTW, I have 2 more projects nearing completion. So, reserve some more time for me this winter.  ;)

Best, Jeff

Careful. . . audio crack dealers shouldn't dip into their own stash :)  Bad for business.

Just an observation, the GDIY 51x crew (jsteiger, silent:arts, and others) are putting out some really awesome products.  From my limited exposure to DIY, I think these kits are really top-shelf and the professionalism displayed on all fronts (design, manufacture, sale, and support) set the bar high.  I do my best to raise the bar on documentation to de-mystify these projects a little and draw in some fence-sitters. . . and hopefully let people have a glimpse of how much fun these builds are!
 
hi chunger,
great stuff!  looking forward to your thoughts on the build as well with regards to sound and use.
btw, sorry for the OT, but what kind of camera are you using for your documentation?
best,
grant
 
baadc0de said:
dissonantstring said:
btw, sorry for the OT, but what kind of camera are you using for your documentation?

Canon EOS DIGITAL REBEL XTi alias 400d ?

Someone's been reading the metadata on the photos  ;)  This is the build thread, so I won't clutter up the works too much, but everything I know about lighting, I learned from here:

http://www.strobist.com

David Hobby and strobist are the DIY or photographic lighting.

Entry level DSLR's can perform great when you hit the sensors with the right quality and quantity of light.  I'm shooting 1/200 sec, iso 200,  in the f10-16 range on decent glass (Canon 17-55 f2.8 ), so I'm maximizing each available pixel (nowhere near the outer fringes of the performance envelope of my equipment).  It's akin to setting up your gain stages right on a good, strong signal source, through the right mic, and hitting tape optimally.  The trick for me is not the camera. . . it's the light.  Sortof like recording in an optimally tuned room with adequate equipment. . . much more forgiving and responsive than recording in a horrible room with highest grade equipment.  Yes, for higher-profile gigs, I would certainly rent better camera and glass, but for the projected end-use of this photo set, I can generate high enough quality images w/ my ghetto rig because  I know it's capabilities and limitations.
 
dissonantstring said:
hi chunger,
great stuff!  looking forward to your thoughts on the build as well with regards to sound and use.
Grant

Check out Today Is Your Day, (Shania's latest single) if you want to know what they sound like. http://www.youtube.com/watch?v=OMciyWyugKY&ob=av2e I believe Reid had them strapped across the mix bus. I am waiting for clarification from him right now. I do know he fell in love (with the ML's!) and now has his own pair. I did a little mod for hard bypass in place of the Mute for him.

Cheers, Jeff

Edit: Reid confirms the ML's were on the mix bus.
 
OK. . . last push.  I took a moment to pause because the following assembly steps were complex and I wanted to make sure everything was clear in my mind before melting stuff together.  After reading the instruction set through a few times, I determined that hilarity would probably ensue especially trying to photograph some of these steps by myself  :p

OK. . . next grayhill switch.  This is the trim attenuator.

p872855927-4.jpg


Make sure you don't lose those 2 barely visible pins.  We need to insert one between "1" and "12"

p828205445-4.jpg


. . . and another between "8" and "7"

p1024051648-4.jpg


It'll look something like this from the bird's eye view.

p797238899-5.jpg


Next, install the stop retainer seal "sticker".  Make sure the retainer does not sit on top of the raised center portion.

p605219753-5.jpg


p713645153-4.jpg


Next, we temporarily place the switch on the the sub-board without soldering.

p925510163-4.jpg


We are checking for resistors shorting against the switch's outer metal casing.  The gaps are narrow.

p1006443755-5.jpg


Having established the components do not interfere, we align the L-bracket to the faceplate again and secure with a clamp.  Align the hole reveals as perfectly as possible here.

p674023500-5.jpg


Place the spacer washer on the grayhill switch.

p734138675-4.jpg


And insert the LED.  The small cathode end of the LED should go in the hole the arrow is pointing to.

p610736970-4.jpg






 
Next, plosition the sub-board (w/ loose grayhill switch and loose LED) and lightly install the nuts.

p537141637-4.jpg


Fiddle with positioning until the board is perpendicular to the L-bracket and all spaces look even and correct.

p715627876-4.jpg


p830962714-4.jpg


According to the instructions, there should be a .410" gap between the L-bracket and the sub-board.

p921307172-4.jpg


After verifying everything is properly positioned, I tightened the nuts just snug.

p890093229-4.jpg


Next, push the LED into the faceplate.

p967638020-4.jpg


This should protrude slightly in the front.  Solder the LED in, and trim the leads.

p608302105-4.jpg


p627039710-4.jpg


Then, double check alignment and gaps again, and solder the grayhill switch.

p613088269-4.jpg


p724849572-4.jpg


 
Next, locate the 2 L-headers.  There should be a long one and a shorter one.

p1031317194-4.jpg


Place the long one on the back side of the main PCB at J1-3.

p624017827-4.jpg


Because we're getting close to that part with the hilarity, I used a little tape to keep this from falling out.

p568817467-4.jpg


Next, place the shorter L-header on the backside of the main fader sub-board.

p767850300-4.jpg


Ok. . . here's the hilarious part.  This was an unbelievably difficult set of pictures to get :)

p625579734-4.jpg


p963770007-4.jpg




Whew. . . all components are in position.

p913072215-4.jpg


Next,  re-attach the main PCB to the L-bracket.

p858727145-4.jpg


And, secure the nuts on the front faceplate.  Make sure the main fader sub-board is pressed firmly against the main PCB.

p827234502-4.jpg


p846536756-4.jpg


Check component alignment all around to make sure the sub-boards are perpendicular.  It doesn't hurt to be very careful at this stage as a mis-step here could cost a lot of time and effort to undo.

p849821812-5.jpg


p844375153-4.jpg


Next, I begin soldering the L-headers.

p1069953844-5.jpg


p1014000457-4.jpg


p1023788367-4.jpg


p965570020-4.jpg


Next,  solder from the bottom of the PCB the near lead on the L-brackets.  The rest can be completed at a later step.

p819156381-4.jpg


p1018437248-5.jpg


And, soldered in.

p1054869965-4.jpg


Next, insert leads saved from the large capacitors into these slots.

p788779595-4.jpg


And solder securely from both sides to make sure there is a solid mechanical connection.

p831526118-4.jpg


p926196106-4.jpg


Next, disassemble the unit again, and solder in the L-header leads that were inaccessible in previous steps.

p732086458-4.jpg


p604940525-4.jpg


Utilizing a cut-off from one of the transformers, create a ground wire between the trim-switch sub-board and the main PCB.

p575985266-4.jpg


p486285920-4.jpg


 
Electronic assembly is complete at this stage. . . next, re-assemble the main PCB to the L-bracket and the faceplate again.

Oh, don't forget about the little spacer on the grayhill trim switch.

p508470574-5.jpg


This time, upon re-assembly, apply lock washers to the standoffs.

p507276136-4.jpg


p354581434-4.jpg


Nuts go on finger tight first. . .and then, using console tape on your sockets to protect the faceplate markings, and snug down the switch nuts with the protected tool.


p179660165-4.jpg



p342662406-4.jpg


p188669320-4.jpg


Poof!

p106374098-4.jpg


p106374098-4.jpg


p350425710-5.jpg
 
Next, locate the baggies with the knobs.

p522249985-4.jpg


First, install the HPF knob.  Use pliers to turn the switch to the 12Hz position and tighten down the knob.  This one should be pretty straight forward.

p140168600-4.jpg


Next, install the LPF knob.  This one will be a little trickier because one of the allen screws tightens against the flat portion of the shaft.  No problem. . . position the shaft with pliers to 18Khz position.  align the knob to point towards the "1" of "18" marking and tighten the allen screw that does not land on the flat portion of the shaft.  Then, as the other screw is tightened, the knob will migrate towards center.

p470189555-5.jpg


Position the trim twitch shaft to -3db and attach that knob as well.

Next, locate the main fader to 0db by observing the copper contact point in the clear window of the switch, and secure the main fader knob.

p313163151-4.jpg


Sticker time. . .

p531814526-4.jpg


p88725736-4.jpg


p360718026-4.jpg


Next, I take a look at the documentation and decide how I want to configure the 5 jumpers.  J6 activates an unbalanced output to pin 3 on the edge connector for a future application.  I set that to "NC".

p156515136-4.jpg


J5-1, J4-3, and J3-3 determine if the discrete receiver stage is inline or bypassed.  I opt for "D" or inline.  J8-1 is the DC-link option to activate mute logic on pin 6 of the edge connector.  I set that to "N" or not-linked since that's how jsteiger ships these stock.

p400768208-4.jpg


p13405391-4.jpg


Next, I hook the unit up without opamps installed and see if I read the correct voltages to the op-amps.

p126803095-4.jpg


All voltages read normal in +-16V as well as +-24V modes.

The red tape indicates this is my bricked GAR2520. . . I haven't been able to figure out what's wrong with it, but it's the first op-amp that goes into every one of my builds because the sockets are bloody stiff the first time pins are inserted, and inevitably, I bend pins or need to apply a lot of pressure to seat the op amp the first time.  So, I beat up on my bricked op-amp.

p338753942-4.jpg


After I insert and remove the bricked op-amp a few times in both sockets, I install a pair of fully functional GAR2520's and make sure to set my voltage to 16V!

p327840404-4.jpg


And, there we are. . . assembly is complete on the VC528. . . Humans win!

p449922087-4.jpg


p274218968-4.jpg


p216648709-5.jpg


p532797865-5.jpg


p133827599-5.jpg


p485538529-4.jpg


I'm going to go to sleep now.  .  .Thanks, bye.  :eek:








 

Latest posts

Back
Top