Re: www.pcbgrinder.com - Kits & PCBs
« Reply #120 on: June 26, 2013, 04:23:03 AM »
I've just noticed you have EzAK5 boards.
Looks interesting. Seems similar to EQ-3D.
Where can be found more info on it?
AML doesn't have anything on their web, over here also there's none...

Its colins 500 series adaptation of a NiteEQ type of dealio. The Schematic and the BOM are on the site...

Gustav


shot

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #121 on: June 26, 2013, 07:21:59 PM »
Ok, I feel a bit embarrassed, but I can't seem to find anything on AML web!
Help! Link maybe...
 ???

Harpo

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #122 on: June 26, 2013, 08:20:03 PM »
Ok, I feel a bit embarrassed, but I can't seem to find anything on AML web!
Help! Link maybe...
 ???
http://www.groupdiy.com/index.php?topic=19789.msg438218#msg438218
A common mistake that people make when trying to design something completely foolproof is to underestimate the ingenuity of complete fools.  -Douglas Adams

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #123 on: July 09, 2013, 03:38:03 AM »
Mailserver was down yesterday, so if you have had any problems or miss a reply, please try again.


Gustav

Nescafe

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #124 on: July 12, 2013, 07:22:43 AM »
Hi Gustav,
I sent You a PM about some EQ PCB a few days ago, do You receive it?

Temmy

anjing

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #125 on: July 16, 2013, 11:39:58 PM »
Hi Gustav,
   
    Thanks for the two BoHansen di's shipped to Canada, i got them on monday!

Regards,

Pierre

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #126 on: July 17, 2013, 03:09:30 AM »
Hi Gustav,
I sent You a PM about some EQ PCB a few days ago, do You receive it?

Temmy

I have to figure out how to do the shipping to Indonesia before I can give you a quote. I have no deal with UPS for that area, so it would be over 100 euros as is.

Gustav

Nescafe

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #127 on: July 19, 2013, 11:15:17 AM »
OK, I will try another way.

Thank You

anjing

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #128 on: July 24, 2013, 01:44:44 AM »
Nescafé! Are you in a hurry? If not i will visit relatives in indonesia within the next few months, i could bring the pcb's for you.

Pierre

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #129 on: July 25, 2013, 04:55:28 AM »
OK, I will try another way.

Thank You

I had your boards packed up to go to Volker, but it seems like you ended up declining his offer. I will look into it again if you wish - just send me a mail.

Gustav


Nescafe

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #130 on: July 28, 2013, 03:09:27 AM »
Nescafé! Are you in a hurry? If not i will visit relatives in indonesia within the next few months, i could bring the pcb's for you.

Pierre

Thank You for the offer Pierre, but I think I will finish the other project first..

OK, I will try another way.

Thank You

I had your boards packed up to go to Volker, but it seems like you ended up declining his offer. I will look into it again if you wish - just send me a mail.

Gustav

Hi Gustav,
yes I have asked Volker help, but finally I decide to fund my DAOC first

Thank You.

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #131 on: August 07, 2013, 02:02:20 PM »
Nescafé! Are you in a hurry? If not i will visit relatives in indonesia within the next few months, i could bring the pcb's for you.

Pierre

Thank You for the offer Pierre, but I think I will finish the other project first..

OK, I will try another way.

Thank You

I had your boards packed up to go to Volker, but it seems like you ended up declining his offer. I will look into it again if you wish - just send me a mail.

Gustav

Hi Gustav,
yes I have asked Volker help, but finally I decide to fund my DAOC first

Thank You.

Cheers!

Gustav

tommypiper

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #132 on: August 21, 2013, 02:15:42 PM »
Hi Gustav, your PM box is full!

Are you going to offer the ez1073 (non-500 version) again????!!

thanks!
Imagine a wet, slightly chilled from its gas release and decompression, with water droplets condensing, sucking surface tension, slowly sliding down the side, capped by a healthy virgin froth on top..

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #133 on: August 21, 2013, 03:25:30 PM »
Hi Gustav, your PM box is full!

Are you going to offer the ez1073 (non-500 version) again????!!

thanks!

Hey Tommy.

PM is currently full by choice. Can't manage too many lines of communications without losing messages.

I never had the Ez1073 - Try Colin's shop :)

Gustav

tommypiper

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #134 on: August 22, 2013, 12:19:25 AM »
Gustav, thanks.
« Last Edit: August 22, 2013, 01:36:25 PM by tommypiper »
Imagine a wet, slightly chilled from its gas release and decompression, with water droplets condensing, sucking surface tension, slowly sliding down the side, capped by a healthy virgin froth on top..

frazzman

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #135 on: August 23, 2013, 02:29:45 AM »
Hey Gustav, any chance of doing a run of Nite 3D Air EQs? Im sure you wouldn't have any trouble getting rid of them....

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #136 on: August 24, 2013, 03:57:34 AM »
Hey Gustav, any chance of doing a run of Nite 3D Air EQs? Im sure you wouldn't have any trouble getting rid of them....

I have Colins 500 series adaptation in the shop, and if you want it in a regular rack mount, you can use that card with an edge adaptor.

EzAK5

Gustav
« Last Edit: August 25, 2013, 03:21:50 AM by Gustav »

Enchilada

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #137 on: August 27, 2013, 10:06:45 PM »
Are you still able to do the SSL 9K preamp PCB? I can only see the 9K5 preamp on pcbgrinder.com.

Ta

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #138 on: August 28, 2013, 02:58:48 PM »
Are you still able to do the SSL 9K preamp PCB? I can only see the 9K5 preamp on pcbgrinder.com.

Ta

I just sold the last two, and I doubt I will be making more.

You can use the 500 series card to build the same circuit and add an edge connector to make the connections if you want to mount it in a case.

Gustav

Enchilada

Re: www.pcbgrinder.com - Kits & PCBs
« Reply #139 on: August 28, 2013, 10:07:23 PM »
Might have to look into that. Thanks  :)