skipwave
Well-known member
EMAIL ME at my gmail address "brian dot skipworth" (is this bot evasion even necessary any more?) - DO NOT PM
OEP A262A2E (in mu metal shielding can which I think makes it a A262A2C) - You know it and love it. I was going to put it on the input of the G-1176, but I don't have time. PayPal me $20 shipped in the USA.
-------------------------------------
[SOLD] Modded MXL 603S stereo pair: PayPal me $130 shipped in the USA. Anywhere in the world for a little extra (I'll calculate the added shipping cost).
Capacitor between the capsule and FET replaced with Xicon polypropylene. Stereo bar and windscreens included.
https://drive.google.com/open?id=0BxhapQSKAI5ad3ZoSEx4SHExb01lSFhPYmFBVmppeFhILTBN
https://drive.google.com/open?id=0BxhapQSKAI5ackdfRUNPVVR5RnJVUERVN0F0WHpsemFESWR3
--------------------------------------
[SOLD] ADC transformer: PayPal me $40 shipped in the USA. Anywhere in the world for a little extra (I'll calculate the added shipping cost).
Pretty uncommon config:
Primary Impedances:
Two 10k windings
600 ohm (could be used for feedback)
Secondary:
600 ohm
250 ohm
Could be used in a push pull config with relatively low power output driver, like some two-triode bottles. OR, primaries could be paralleled for the very common capacitor decoupled single-ended 10k:600 like on a OneBottle and leave the 250 ohm secondary unconnected. Your choice.
Overall, amazingly good condition. The lugs were soldered, but clean. I ran a signal through and it sounds very hi-fi with extra iron. http://groupdiy.com/index.php?topic=14341.100
-------------------------------------
[SOLD] A pair of SESCOM 66J0342 step down input transformers, pulled from a line driver/balancer box. 4:1 turns ratio, center tapped, they were used for 10k:600 in front of some NE5532 chips driving output transformers. Sound pretty good, not Jensen, but pretty damn good. PayPal me $30 shipped in the USA.
OEP A262A2E (in mu metal shielding can which I think makes it a A262A2C) - You know it and love it. I was going to put it on the input of the G-1176, but I don't have time. PayPal me $20 shipped in the USA.
-------------------------------------
[SOLD] Modded MXL 603S stereo pair: PayPal me $130 shipped in the USA. Anywhere in the world for a little extra (I'll calculate the added shipping cost).
Capacitor between the capsule and FET replaced with Xicon polypropylene. Stereo bar and windscreens included.
https://drive.google.com/open?id=0BxhapQSKAI5ad3ZoSEx4SHExb01lSFhPYmFBVmppeFhILTBN
https://drive.google.com/open?id=0BxhapQSKAI5ackdfRUNPVVR5RnJVUERVN0F0WHpsemFESWR3
--------------------------------------
[SOLD] ADC transformer: PayPal me $40 shipped in the USA. Anywhere in the world for a little extra (I'll calculate the added shipping cost).
Pretty uncommon config:
Primary Impedances:
Two 10k windings
600 ohm (could be used for feedback)
Secondary:
600 ohm
250 ohm
Could be used in a push pull config with relatively low power output driver, like some two-triode bottles. OR, primaries could be paralleled for the very common capacitor decoupled single-ended 10k:600 like on a OneBottle and leave the 250 ohm secondary unconnected. Your choice.
Overall, amazingly good condition. The lugs were soldered, but clean. I ran a signal through and it sounds very hi-fi with extra iron. http://groupdiy.com/index.php?topic=14341.100
-------------------------------------
[SOLD] A pair of SESCOM 66J0342 step down input transformers, pulled from a line driver/balancer box. 4:1 turns ratio, center tapped, they were used for 10k:600 in front of some NE5532 chips driving output transformers. Sound pretty good, not Jensen, but pretty damn good. PayPal me $30 shipped in the USA.