TRIDENT 65 MONITOR CHANNEL CB9362 ISS6 SCHEMATICS NEEDED

[ParkOne]

HI GUYS and Girls ;-)
my first post because i'm so SAD.
I bought a nice Trident 65 console 8 month ago at Funky Junk France, (quite expensive 8000euros), i trusted them for the recapped of the desk.

What's my disapoitment when i released they put only 100µF 16Volts chinese condensators to replaced all condensators references on all channel, master and monitor (25µF, 100µF, 47µF, 470µF normally in place).
You can imagine these condos now, they are all burned (the condos in schematics are all in 25Volts).
The desk sounded very bad and after 2 weeks of use the desk didn't switch on anymore.

I started to recapped all condos myself using Panasonic FC (in 25Volts) with right value like indicate in the Trident65.pdf schematic i found in this forum before. (by the way really thanks for this).

My Problem: in this schematics there is only Monitor Channel CB9351.

So i need the schematics for my modules in place the Monitor CB9362 (can't use the Components list for CB9351).

If someone in this forum could send me or scan only the components list for this CB9362, you'll be very welcome, of course.

When finished i will post pictures, with Panasonic FC, and also MKP and Sylver Mika...hope it will sound incredible now...

I will recapped the power supply also....

Thanks for you all and especially thanks to www.Ginkgo-ev.com who help me for components choices and revision.

Waiting for your news.

Cheers,

 

[pucho812]

I don't have the schematic. You could just replace the caps with the same values but rated at 25V instead of 16V. For example replace the  100uf/16v caps with 100uf/25v. 

 

[ParkOne]

Thanks for the answer Pucho812, but my problem is Funky Junk put only 100µF 16Volts for replacment of ALL chimic condensators on the monitors channel!
Too bad....
This is why i need to have components list to know which condos is officially 100µF or 22µF or 47µF or 470µF...
The best will be :
C1 = XXXµF
C2 = XXXµF
etc
etc

Cheers,

 

[Rob Flinn]

As Pucho said if you make them all 25v you wil be fine.  That is the spec of the Caps in my Trident Trimix in all places

Thanks for the answer Pucho812, but my problem is Funky Junk put only 100µF 16Volts for replacment of ALL chimic condensators on the monitors channel!
Too bad....
This is why i need to have components list to know which condos is officially 100µF or 22µF or 47µF or 470µF...
The best will be :
C1 = XXXµF
C2 = XXXµF
etc
etc

Cheers,

 

[ParkOne]

Guys, thansk for yours posts,

my problem is not 16Volts instead of 25Volts, but to find the right value for each Condensators emplacement in my monitor Input.

When you watch the schematics from Trident for input channel and master channel you know there is a big problem with recapp from funky junk on my desk, i'm not posting to be bad, just hoping someone could send me the components list for this CB9362 and i will of course input Panasonic FC in 25Volts but with right values as indicate in the schematics and not values from the chinese condos in place right now.

I will post pictures and find a link to the Original Schematics in the futur.

Many Thanks, cheers,

 

[pucho812]

sorry I misunderstood what the problem was.... However I suspect that the cap values used are close enough so they shouldn't be an issue.

 

[ParkOne]

Thanks Pucho192,

this is an issue, i want to input good quality caps, and a diffrence between 100µF and 22µF could be a problem.

I will see myself what i can do with this monitor channels, but a components list will be very welcome.

Cheers,

 

[87Gerhard87]

Hi Everyone,

Can anyone please give me some information as to what this removable board is? It's in my Trident 65 Master Section.

Thanks,

 

[JohnRoberts]

quad op amps with cmos multiplex chip...

my guess is for some kind of signal switching

JR

 

[1680TB]

Guys, thansk for yours posts,

my problem is not 16Volts instead of 25Volts, but to find the right value for each Condensators emplacement in my monitor Input.

When you watch the schematics from Trident for input channel and master channel you know there is a big problem with recapp from funky junk on my desk, i'm not posting to be bad, just hoping someone could send me the components list for this CB9362 and i will of course input Panasonic FC in 25Volts but with right values as indicate in the schematics and not values from the chinese condos in place right now.

I will post pictures and find a link to the Original Schematics in the futur.

Many Thanks, cheers,

well, i'm looking for Monitor CB9362 schematics
i can note all the value i saw on mine, but i'am not sure they are the right one.
tom