bernbrue

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #20 on: September 07, 2012, 02:37:22 PM »
ISK Tm-66 ?
dimension Still unknown ?
Dan,
Hi,
it seems to be the same as the T-Bone SCT-700. It measures 59 x 180 mm
regards
Bernd


MicDaddy

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #21 on: September 08, 2012, 11:28:43 AM »
I've been sitting on a 'Dale' m7 and this may be just what I was looking for.


Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #22 on: September 10, 2012, 02:33:00 PM »
this is i would think the last version,  it 44 * 48 mm , with grapping hole at 1/4" and specific at 28mm center from the bottom of the board,  Meant to  fit tbone, nady and gt-2b style mic   i will be doing a very small run to start with. Let see What happens, 


Let me know if there is any interest. :)
Cheers,
Dan,



KasperNyhus

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #23 on: September 10, 2012, 06:45:38 PM »
I'm in for one!

signalflow

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #24 on: September 10, 2012, 07:10:38 PM »
Holy Crap! You're killin me! I'm in for 2 depending on price. 

-Casey
The shortest distance between two places is a nap.

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #25 on: September 10, 2012, 07:13:59 PM »
Interested!

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #26 on: September 10, 2012, 07:37:29 PM »
1 please

JamesW

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #27 on: September 10, 2012, 08:12:08 PM »
A pair please.
Subject to change with out notice

mukole

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #28 on: September 10, 2012, 09:01:49 PM »
I'm definitely interested in 2 as well please!!

MicDaddy

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #29 on: September 10, 2012, 10:53:55 PM »
I'd like 2 please


Govinda Doyle

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #30 on: September 11, 2012, 08:48:54 AM »
1 for sure!  :D

baadc0de

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #31 on: September 11, 2012, 09:01:51 AM »
Pair here.. add to the U67/87 boards.

EDIT: One more question, does anyone know if the PCBs would fit into the LDC part (MXL 550) of the MXL pair quoted before?
« Last Edit: September 11, 2012, 09:17:19 AM by baadc0de »

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #32 on: September 11, 2012, 10:46:57 AM »
I beleive the MXL is 47mm outer that should leave enough room for the 44mm PCB but this will be part of the experiment on MXL body type For sure.

DAn,

MatthisD

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #33 on: September 11, 2012, 11:15:46 AM »
I beleive the MXL is 47mm outer that should leave enough room for the 44mm PCB but this will be part of the experiment on MXL body type For sure.

DAn,

The se2200a body is the same diameter. The PCB mounting holes are only 29.5mm apart. I think the 44mm PCB would have to be trimmed down by a couple of mm on each side unless you can mount the PCB right on the centre diameter some how.
Matt

0dbfs

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #34 on: September 11, 2012, 12:51:53 PM »
Two for me please!
Thx!
-jb
Music is everything!
Audio is everything else!

dissonantstring

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #35 on: September 11, 2012, 12:54:19 PM »
hi dany,
interested in one DU-47 FETi pcb set. 
thanks!
best,
grant

craigmorris74

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #36 on: September 11, 2012, 01:55:58 PM »
I'd like one.

Craig

jonhunter

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #37 on: September 12, 2012, 01:15:54 AM »
I'd Like two !!

thanks
jon
Jon Hunter

Hank Dussen

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #38 on: September 12, 2012, 02:47:59 AM »
1 here!

Re: D-U47FETi Microphone Project ( Looking For Donor Body Suggestion Welcomed)
« Reply #39 on: September 12, 2012, 02:52:32 PM »
I beleive the MXL is 47mm outer that should leave enough room for the 44mm PCB but this will be part of the experiment on MXL body type For sure.

DAn,

The se2200a body is the same diameter. The PCB mounting holes are only 29.5mm apart. I think the 44mm PCB would have to be trimmed down by a couple of mm on each side unless you can mount the PCB right on the centre diameter some how.
Matt

The things is i have no clue of the railing dimension inside all i was refered too is the Alctron PCB size and they have been created according to that at this point ,  i did a small batch tough so if they are any correction in term of  dimension i will be open to suggestion no problem,
Dany ,


 

Related Topics

  Subject / Started by Replies Last post
1335 Replies
238885 Views
Last post August 13, 2019, 01:29:42 PM
by Joekkel
93 Replies
17973 Views
Last post August 23, 2013, 11:22:27 AM
by Enchilada
339 Replies
79894 Views
Last post August 07, 2019, 03:20:39 PM
by Rlucas41
48 Replies
21866 Views
Last post November 11, 2018, 12:46:15 PM
by Marcedona