callgrlmusic
Member
i would like all of them please
FEELER - Solid-state microphone upgrade boards (OpAmp, JFET, U87A, FET847, ORS87-Plus)
- Thread starter Khron
- Start date
Help Support GroupDIY Audio Forum:
Apologies for the delay, but i have updates! Or, well, at least one, anyway 
In-between getting acquainted to living in my own house, i finally managed to eek out some time to populate a first board from this load - a cardioid-only OpAlice.
After a quick capsule-less test to sanity-check the supply voltages (and promptly discovering the brainfart of having installed the opamp the wrong way around - yes, happens to the best of us
), getting a bit over 39v at XLR pins2/3, which points towards ~2.6mA total current draw, using an OPA2991. Provisionally, i decided to bypass all the tone-shaping features, to only leave the bare minimum to troubleshoot, if needed.
Stuck the board into an already-slightly-modded Neewer NW700, and instantly noted a couple issues.
One is that, having placed the mounting holes so that the top edge of the boards goes right up to the bottom of the headbasket, it won't sit flush, due to to the macgyvering i needed to do, to fasten an LDC mount to the base plate. Which involved a bunch of moderately-sized washers... Oh well, i'll see about including a notch of some sort in that area.
Second, as i had stuck a 1/2" wide strip of rubber to the inside of the body tube (to quell down resonances) some time ago, i was slightly disappointed to discover the board's a bit too wide to fit inside the smaller inside-diameter of the rubber strip. Not much i can do about that, without sacrificing MXL2001 chassis compatibility. But perhaps if i taper down the board width just below the 2001 mounting holes...
But hey, that's what prototypes are for, right? Proof-of-concept and all that...
No extraneous noise upon a brief test, but then again, my chaotic work-room is far from a testbed for noise. But it works! Capsule ends up seeing about 20v across it, so especially since it's a straight buffer (no gain), this won't be the most sensitive thing out there, but that's not the worst thing for drums and such, right?
In-between getting acquainted to living in my own house, i finally managed to eek out some time to populate a first board from this load - a cardioid-only OpAlice.
After a quick capsule-less test to sanity-check the supply voltages (and promptly discovering the brainfart of having installed the opamp the wrong way around - yes, happens to the best of us
), getting a bit over 39v at XLR pins2/3, which points towards ~2.6mA total current draw, using an OPA2991. Provisionally, i decided to bypass all the tone-shaping features, to only leave the bare minimum to troubleshoot, if needed.Stuck the board into an already-slightly-modded Neewer NW700, and instantly noted a couple issues.
One is that, having placed the mounting holes so that the top edge of the boards goes right up to the bottom of the headbasket, it won't sit flush, due to to the macgyvering i needed to do, to fasten an LDC mount to the base plate. Which involved a bunch of moderately-sized washers... Oh well, i'll see about including a notch of some sort in that area.
Second, as i had stuck a 1/2" wide strip of rubber to the inside of the body tube (to quell down resonances) some time ago, i was slightly disappointed to discover the board's a bit too wide to fit inside the smaller inside-diameter of the rubber strip. Not much i can do about that, without sacrificing MXL2001 chassis compatibility. But perhaps if i taper down the board width just below the 2001 mounting holes...
But hey, that's what prototypes are for, right? Proof-of-concept and all that...
No extraneous noise upon a brief test, but then again, my chaotic work-room is far from a testbed for noise. But it works!
Capsule ends up seeing about 20v across it, so especially since it's a straight buffer (no gain), this won't be the most sensitive thing out there, but that's not the worst thing for drums and such, right?
Last edited:
That'a a hefty capsule mount you have there.
Or you took LARGE in LDC too seriously.
Prototyping is not for the weak!
Go big or go home
Yeah, at the time (when i installed this particular capsule in this mic), the only M3 bolt i had, with a low-enough-profile head to fit inside the counterbore in the capsule mount, was THAT long. Big spring washers because that was the one way to "make up" threaded length. Don't ask, i just grabbed what i had at hand to get it done THEN
Attachments
Last edited:
![Electronics Soldering Iron Kit, [Upgraded] Soldering Iron 110V 90W LCD Digital Portable Soldering Kit 180-480℃(356-896℉), Welding Tool with ON/OFF Switch, Auto-sleep, Thermostatic Design](https://m.media-amazon.com/images/I/41gRDnlyfJS._SL500_.jpg)
Similar threads
