GssL 20th Anniversary edition

[inf0]

I was actually gonna ask that too , it helps me a ton seeing the finished unit . A lot of things can be cleared up just by looking at it !

 

[inf0]

I wanted to ask , would I need to use an extra pcb like expat's VU meter pcb in order to use a SIFAM R22 Vu meter? I got a vintage one that I've been dying to use for a project!

 

[Gustav]

Errors in the BOM for "Release": It's not 2 x 1M2, just one. But two 2 x 750K instead of 1
Error in the BOM for "Ratio":4 x 3M9 not 6x. Also maybe 2 x 3M3 (which are not in BOM)
Error in the BOM for "Side Chain HPF": missing 2 x 1nf (but in orderlist from reichelt)

Unclear: Label ATT = 0,0R ? If yes, only 1 x 0,0R in Sidechain

Error in Reichelt Part Order:
2x1M4 in Ratio missing

I caught your first edit and added the correction after, but if you keep editing this one post and adding to it, we cant be sure I can keep track, so better gather a few things and post.

Added 2 x 1nF in BOM for SC
Reichelt doesnt have 1M4 resistors, but I can see I doubled up on 750K to put in series instead in the cart.
Already see 2 x 0R in the sidechain BOM, but added 1 x 0R to the attack portion of BOM.

ATT is just jumpers going to the Attack. We do a hard bypass on this unit, but I marked this spot with the ATT resistor going to attack, because thats where we cut the signal in soft bypass on the original project, and some expressed a want to maybe do their build with both options.


Gustav

 

[janczmok]

Okay, i add another post if i find something more.

 

[janczmok]

Error in Reichelt Order List:
1206 Input, 4 x 100R in BOM, in Order List only 2

Error in BOM - Blend
Its 16x10K in Total (also Order List wrong)
Side Chain: 2x10K missing in Bom+Orderlist


Error in BOM + Orderlist
Release has only 1 x 1M2 not 2
Ratio has 4 x 3M9 not 6 x 3M9

Error inn Orderlist somewhere, Not 2 x 2k2 just 1 x 1k1

 

[inf0]

@Gustav Excuse me if it's a silly question but do the 2 gain terminals connect together at a single pot ? You've mentioned that for the gain we need 1 x 10k lin ( not a stereo pot ? )



Also , I've seen that in your prototype you've chained together the XLR grounds as I can see in the original build guide as well , I assume this is not necessary if I mount the XLR directly on the pcb?

Thank you!

 

[janczmok]

Question in the "Color" Section:
i do see 2 x TRM , is that TERMination or TRIM ?
and the 22uf is that 22u/35V ?

And is that 10uf mks in SC_HPF ? or is that 10 uf bipolar ?

 

[Gustav]

@Gustav Excuse me if it's a silly question but do the 2 gain terminals connect together at a single pot ? You've mentioned that for the gain we need 1 x 10k lin ( not a stereo pot ? )

View attachment 143451

Also , I've seen that in your prototype you've chained together the XLR grounds as I can see in the original build guide as well , I assume this is not necessary if I mount the XLR directly on the pcb?

Thank you!

These are simply mislabeled, because I copy pasted the part from the gain and forgot to rename.

If you look at the actual connections, these are alternatives to PCB mount XLR, so you wire via a connector.

Ill add it to the errata list.

Gustav

 

[Gustav]

Error in Reichelt Order List:
1206 Input, 4 x 100R in BOM, in Order List only 2

Error in BOM - Blend
Its 16x10K in Total (also Order List wrong)
Side Chain: 2x10K missing in Bom+Orderlist


Error in BOM + Orderlist
Release has only 1 x 1M2 not 2
Ratio has 4 x 3M9 not 6 x 3M9

Error inn Orderlist somewhere, Not 2 x 2k2 just 1 x 1k1

Unsure of the wordings here, like "Not 2 x 2K2, just 1 x 1K1" Too many 2K2, 2 x 2K2 missing? And also unsure if you are adding things that were already corrected (4 x 3M9, not 6 x 3M9)

- also, I think it would be more helpfull if you would gather up a bit of these, so you have at least a days interval, just to make sure some things dont drown out in the stream!

Gustav