I have a question about these micro tube mic ?

GroupDIY Audio Forum

Help Support GroupDIY Audio Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I think we are talking about powering the whole tube with P48 and I believe that's what done with Kinkgorgs mic.
Oh, what I mean is that if heating doesn't become a problem in ECC88 and other electronic tube microphones, then microtubes won't either, that's all:)
 
By the way, some electronic tubes are designed to operate at extremely low voltages and currents, but those are likely to have significant distortion issues. It is best to refer to the data sheet to confirm this. Electronic tube microphones have been around for nearly a hundred years, and many engineers have conducted research on them. There is a reason why phantom powered electronic tube microphones have not appeared. If they cannot bring better performance than FET, they will be meaningless:(
 
I think this one you posted in another thread is even more intriguing. Wonder what the device is? Maybe a nuvistor? Also doesn't seem to be connected.
Oh, and also, this electronic tube comes from China/Soviet Union, starting with 1z8 and with a maximum of 1z11. It is a high back pressure pulse rectifier tube, usually used for high-voltage pulse rectification in televisions, and can provide approximately a few mA of current. As you can see, the metal cap on the top of this electronic tube is designed to pass high voltage.

Correction: The maximum current of 1z11 is 300 μA
 
By the way, some electronic tubes are designed to operate at extremely low voltages and currents, but those are likely to have significant distortion issues. It is best to refer to the data sheet to confirm this. Electronic tube microphones have been around for nearly a hundred years, and many engineers have conducted research on them. There is a reason why phantom powered electronic tube microphones have not appeared. If they cannot bring better performance than FET, they will be meaningless:(
Yes. The datasheet of the 6418 tube I posted here earlier states 12% total distortion. What ever that means, it doesn't imply very hi-fi performance. (Though the spec is for using it as a power tube in a hearing aid device I think.)
 
Oh, that makes sense. Deaf people usually only need to amplify the sound in the frequency band where the human voice is located, so reducing design difficulty in this way is economical (just like radio)
Yes. The datasheet of the 6418 tube I posted here earlier states 12% total distortion. What ever that means, it doesn't imply very hi-fi performance. (Though the spec is for using it as a power tube in a hearing aid device I think.)
 
https://www.audio-technica.com/en-us/at3060

https://shop.funky-junk.com/shop/re...e/microtech-gefell-um-900-tube-condenser-mic/

https://naiant.com/2016/02/16/x-v-tube-kit-microphone/

I've had no issues with these tubes. Neither distortion, or any other aspect. They have to be suspended carefully to avoid microphonics. They are fun to play with.
The reason why a large number of microphones used miniature tubes in the early days was stability and microphone effect - the tube contained a rather unstable filament structure, and if it was subjected to vibration, it would produce strange sounds or even be damaged. However, microphones such as the AKG C61 use Nuvistor, a specially designed tube used in the aerospace field. It should be pointed out that these tubes still require filaments and high voltage power supply - this is due to the principle of the tube. Without filament heating and high voltage, electrons cannot be emitted to the anode normally.

Correction:its C61
 
Last edited:
Yes. The datasheet of the 6418 tube I posted here earlier states 12% total distortion. What ever that means, it doesn't imply very hi-fi performance. (Though the spec is for using it as a power tube in a hearing aid device I think.)
That's driving headphones, which I think is silly for that tube.
~~~
Distortion depends on a number variables, my audio 6418 preamp is at 0.5% at 2Vac rms at 20Hz.
 
That's driving headphones, which I think is silly for that tube.
~~~
Distortion depends on a number variables, my audio 6418 preamp is at 0.5% at 2Vac rms at 20Hz.
Yes of course. That's not bad at all. @mic test you should check the Naiant schematic posted here earlier. 20% underheated, a good P48 and voilà.
 
Usually, the heat generation of an electronic tube mainly comes from the energy released by its filament (like an incandescent light bulb). Compared to this, the heat generated by the anode voltage is still negligible.
I don't really agree... The electrons hiting the plate generate ~90% of the heat of the tube.
Touch an EL84 of an amplifier with your fingers 1) just heater on 2) HV fed (and audio signal) and you'll notice that (finger burn !) Speaking about a power tube not a pre tube...
Best Regards
 

Latest posts

Back
Top